Includes everything you'll need to show that electricity can act very much like a magnet. One large nail, one five-foot piece and one 1 1/4-foot piece of plastic insulated wire with end connectors, one knife-edge switch, two screws, one 3" x 4" x 1" wooden block and complete instructions. Battery not included.
A big, durable 8" high magnet. Horseshoe-shaped plastic handle is easy to grip for even the youngest hands. Ages 3 and up.
4 inch strong zink-plated steel horseshoemagnet with North and South poles marked. Supplied with keeper.
Includes:
• Two coils mounted in plastic saddle blocks that stand vertically
• Five soft iron cores (round, square, double U, and half-round [2])
• Stiff card and supply of iron filings in reusable vial
• Four alligator clip leads
You will need 6 V battery or power supply exceeding 1 amp DC; galvanometer
Use the materials in this complete kit to experiment with magnetic induction in a coil; primary/secondary coils; magnetic lines of force and electromagnetism. Includes: two coils mounted in plastic saddle blocks that stand vertically; five soft iron cores (round, square, double U, and half-round [2]); stiff card and supply of iron filings in reusable vial; four alligator clip leads. You will need 6 V battery or power supply exceeding 1 amp DC; galvanometer.
Weighs 2 lbs, lifts 200 lbs due to precision machining. the way magnets lift cars in junk yards! instructions, alligator clip leads and battery holder. Requires 1 "D" cell battery (not included).
A fine instrument for determining the results of curvature of spherical surfaces such as mirrors and lenses. Its micrometer screw is graduated to measure displacement as small as 0.01mm. The instrument has two brass plates and three steel legs. A flat glass plate is provided for support while taking precision readings.
A fine instrument for determining the results of curvature of spherical surfaces such as mirrors and lenses. Its micrometer screw is graduated to measure displacement as small as 0.01mm. The instrument has two brass plates and three steel legs. A flat glass plate is provided for support while taking precision readings.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
Clear acrylic trapezoid. With one flat surface frosted to enhance visibility. Bases are 89mm and 40mm. Faces measure 47mm and 35mm.
Clear acrylic trapezoid. With one flat surface frosted to enhance visibility. Bases are 89mm and 40mm. Faces measure 47mm and 35mm.
Made from clear acrylic. One plane surface is frosted. 89mm long. 15mm thick. 25mm across the beam axis.
Made from clear acrylic. One plane surface is frosted. 89mm long. 15mm thick. 25mm across the beam axis.
An oversized set of 6 lenses and prisms designed for mounting on a magnetic chalk or marker board. Lenses are about 8" long, so your optics experiments would be clearly visible from every part of the classroom. Each piece in the set has a pre-attached magnetic backing. Set contains 1 each of semi-circular lens, equilateral prism (3" sides), double convex lens, double concave lens, single convex lens, and single concave lens. An activity guide is also included. Set comes in a sturdy wooden storage case.
An oversized set of 6 lenses and prisms designed for mounting on a magnetic chalk or marker board. Lenses are about 8" long, so your optics experiments would be clearly visible from every part of the classroom. Each piece in the set has a pre-attached magnetic backing. Set contains 1 each of semi-circular lens, equilateral prism (3" sides), double convex lens, double concave lens, single convex lens, and single concave lens. An activity guide is also included. Set comes in a sturdy wooden storage case.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
86mm long and 15mm thick. 18mm wide at center.
86mm long and 15mm thick. 18mm wide at center.
Prism Crown Glass refractive index 1.51. For Spectrometer (15864), and general refraction experiments. Equilateral 32 mm Sides.
Prism Crown Glass refractive index 1.51. For Spectrometer (15864), and general refraction experiments. Equilateral 32 mm Sides.
Index of refraction plate, made from acrylic. Polished surfaces.
This acrylic 125 x 65 x 20mm rectangular block is designed for use as an index of refraction plate, and has a polished surface.
Boxed set of high-quality acrylic prisms, made from clear acrylic sheet, all side polished. The set consists of six prisms in a variety of shapes. Includes: 1 rectangular block (75mm x 50mm x 15mm), 1 semi-circle (90mm base x 15mm thick), 1 equilateral prism (75mm sides, 15mm thick), 1 double convex lens (90mm long, 23mm at center), and 2 double concave lenses (90mm long, 10mm at center).
Boxed set of high-quality acrylic prisms, made from clear acrylic sheet, all side polished. The set consists of six prisms in a variety of shapes. Includes: 1 rectangular block (75mm x 50mm x 15mm), 1 semi-circle (90mm base x 15mm thick), 1 equilateral prism (75mm sides, 15mm thick), 1 double convex lens (90mm long, 23mm at center), and 2 double concave lenses (90mm long, 10mm at center).
A compact and economical Color Mixing Apparatus. This updated version of the classic three color light projector uses three low voltage, high power LED's to project easily-seen red, green, and blue light onto a white screen. The projector mounting allows the beam angles to be adjusted to vary the overlap of the three colored images. The intensity of each LED can be adjusted separately by a potentiometer to give a convincing white light or various shades of mixed colors. Colored shadows can also be explored in a darkened room. The set includes a wall mount power supply and manual.
A compact and economical Color Mixing Apparatus. This updated version of the classic three color light projector uses three low voltage, high power LED's to project easily-seen red, green, and blue light onto a white screen. The projector mounting allows the beam angles to be adjusted to vary the overlap of the three colored images. The intensity of each LED can be adjusted separately by a potentiometer to give a convincing white light or various shades of mixed colors. Colored shadows can also be explored in a darkened room. The set includes a wall mount power supply and manual.
A self-contained unit to measure and study refraction of light. Incident and refractive rays are easily seen and measured. Light rays air into water, water to air and water in water can be studied easily with the help of built-in laser, as a light source, which revolves and can be fixed at any point around a circular graduated scale. With leveling screws to level the water in the tank. Circular scale 160 mm ( 6-3/8 in.) Diameter.
A self-contained unit to measure and study refraction of light. Incident and refractive rays are easily seen and measured. Light rays air into water, water to air and water in water can be studied easily with the help of built-in laser, as a light source, which revolves and can be fixed at any point around a circular graduated scale. With leveling screws to level the water in the tank. Circular scale 160 mm ( 6-3/8 in.) Diameter.
Set of 2 lenses, 1 concave and 1 convex, 38 mm diameter, 150 mm focal length.
Set of 2 lenses, 1 concave and 1 convex, 38 mm diameter, 150 mm focal length.
To investigate the properties of lenses and to construct simple optical instruments. Kit comprised of the following: Two lamp holders, each in cast alloy shade with two axial slots. Complete with two meter 2-core cable and lamp. Shade has integral support arm which is clamped at right angle to the vertical rod, 165 mm long, fitted on heavy cast base, stove hammer finish. One each right and left hand cylindrical lamp shield of light alloy in matt black finish with slot parallel to the axis, size 190 x 60 mm, Height x Diameter. Two black plastic plates, 100 x 80 mm, with 17 equispaced parallel slots. Two black plastic plates, 130 x 80 mm, each with single and triple slits. Two metal support brackets, matt black finish with spring-loaded clips to hold the plates. Four black finish metal light barriers, height 80 mm. Ten Cylindrical Lens ( 8 plano-convex, and 2 plano-concave ), size 50 x 50 mm, Side x Height. Manual included.
To investigate the properties of lenses and to construct simple optical instruments. Kit comprised of the following: Two lamp holders, each in cast alloy shade with two axial slots. Complete with two meter 2-core cable and lamp. Shade has integral support arm which is clamped at right angle to the vertical rod, 165 mm long, fitted on heavy cast base, stove hammer finish. One each right and left hand cylindrical lamp shield of light alloy in matt black finish with slot parallel to the axis, size 190 x 60 mm, Height x Diameter. Two black plastic plates, 100 x 80 mm, with 17 equispaced parallel slots. Two black plastic plates, 130 x 80 mm, each with single and triple slits. Two metal support brackets, matt black finish with spring-loaded clips to hold the plates. Four black finish metal light barriers, height 80 mm. Ten Cylindrical Lens ( 8 plano-convex, and 2 plano-concave ), size 50 x 50 mm, Side x Height. Manual included.
An economically priced Spectrometer, but capable of performing most of the experiments like spectras, angle of prisms, refractive indexes etc. Consists of heavy base with 170 mm diameter circle, divided 0 to 360 degrees, which rotates independently and has locking screw. Collimator: Fixed, with adjustable axis, objective lens with focusing system, variable aperture slit. Telescope: Moveable with set screw and fine motion screw, adjustable axis. Telescope pillar carries vernier scale for accurate measurements. Focusable objective Lens. Ramsden Eyepiece with cross-wires and locking ring for focus lock. Prism Table: Provided with three leveling screws and engraved lines for prism placement in experiments. Comes complete with Prism Clamp, Grating Holder, Tommy Bar for axis adjustment and Instruction Sheet.
An economically priced Spectrometer, but capable of performing most of the experiments like spectras, angle of prisms, refractive indexes etc. Consists of heavy base with 170 mm diameter circle, divided 0 to 360 degrees, which rotates independently and has locking screw. Collimator: Fixed, with adjustable axis, objective lens with focusing system, variable aperture slit. Telescope: Moveable with set screw and fine motion screw, adjustable axis. Telescope pillar carries vernier scale for accurate measurements. Focusable objective Lens. Ramsden Eyepiece with cross-wires and locking ring for focus lock. Prism Table: Provided with three leveling screws and engraved lines for prism placement in experiments. Comes complete with Prism Clamp, Grating Holder, Tommy Bar for axis adjustment and Instruction Sheet.
To demonstrate interference of light. Consists of a pair of glass plates, optically polished, 60mm in diameter, one plane and the other plano-convex mounted together in a baked enamel finish metal frame. Pressure between the plates is adjustable by three nickel-plated brass screws. Instructions included.
To demonstrate interference of light. Consists of a pair of glass plates, optically polished, 60mm in diameter, one plane and the other plano-convex mounted together in a baked enamel finish metal frame. Pressure between the plates is adjustable by three nickel-plated brass screws. Instructions included.