Made from plate glass about 1/16" thick. Highly Silvered back.
This 4in x 2in mirror is made from plate glass about 1/16in thick with a highly silvered back.
Made from plate glass about 1/16" thick. Highly Silvered back.
This 4in x 4in mirror is made from plate glass about 1/16in thick with a highly silvered back.
Made from plate glass about 1/16" thick. Highly Silvered back.
This 6in x 2in mirror is made from plate glass about 1/16in thick with a highly silvered back.
Made from plate glass about 1/16" thick. Highly Silvered back.
This 6in x 4in mirror is made from plate glass about 1/16in thick with a highly silvered back.
Securely hold a mirror in a vertical position on any flat surface. Packages of 6.
Securely hold a mirror in a vertical position on any flat surface. Packages of 6.
Boxed set of high-quality acrylic prisms, made from clear acrylic sheet, all side polished. The set consists of six prisms in a variety of shapes. Includes: 1 rectangular block (75mm x 50mm x 15mm), 1 semi-circle (90mm base x 15mm thick), 1 equilateral prism (75mm sides, 15mm thick), 1 double convex lens (90mm long, 23mm at center), and 2 double concave lenses (90mm long, 10mm at center).
Boxed set of high-quality acrylic prisms, made from clear acrylic sheet, all side polished. The set consists of six prisms in a variety of shapes. Includes: 1 rectangular block (75mm x 50mm x 15mm), 1 semi-circle (90mm base x 15mm thick), 1 equilateral prism (75mm sides, 15mm thick), 1 double convex lens (90mm long, 23mm at center), and 2 double concave lenses (90mm long, 10mm at center).
To investigate the properties of lenses and to construct simple optical instruments. Kit comprised of the following: Two lamp holders, each in cast alloy shade with two axial slots. Complete with two meter 2-core cable and lamp. Shade has integral support arm which is clamped at right angle to the vertical rod, 165 mm long, fitted on heavy cast base, stove hammer finish. One each right and left hand cylindrical lamp shield of light alloy in matt black finish with slot parallel to the axis, size 190 x 60 mm, Height x Diameter. Two black plastic plates, 100 x 80 mm, with 17 equispaced parallel slots. Two black plastic plates, 130 x 80 mm, each with single and triple slits. Two metal support brackets, matt black finish with spring-loaded clips to hold the plates. Four black finish metal light barriers, height 80 mm. Ten Cylindrical Lens ( 8 plano-convex, and 2 plano-concave ), size 50 x 50 mm, Side x Height. Manual included.
To investigate the properties of lenses and to construct simple optical instruments. Kit comprised of the following: Two lamp holders, each in cast alloy shade with two axial slots. Complete with two meter 2-core cable and lamp. Shade has integral support arm which is clamped at right angle to the vertical rod, 165 mm long, fitted on heavy cast base, stove hammer finish. One each right and left hand cylindrical lamp shield of light alloy in matt black finish with slot parallel to the axis, size 190 x 60 mm, Height x Diameter. Two black plastic plates, 100 x 80 mm, with 17 equispaced parallel slots. Two black plastic plates, 130 x 80 mm, each with single and triple slits. Two metal support brackets, matt black finish with spring-loaded clips to hold the plates. Four black finish metal light barriers, height 80 mm. Ten Cylindrical Lens ( 8 plano-convex, and 2 plano-concave ), size 50 x 50 mm, Side x Height. Manual included.
An economically priced Spectrometer, but capable of performing most of the experiments like spectras, angle of prisms, refractive indexes etc. Consists of heavy base with 170 mm diameter circle, divided 0 to 360 degrees, which rotates independently and has locking screw. Collimator: Fixed, with adjustable axis, objective lens with focusing system, variable aperture slit. Telescope: Moveable with set screw and fine motion screw, adjustable axis. Telescope pillar carries vernier scale for accurate measurements. Focusable objective Lens. Ramsden Eyepiece with cross-wires and locking ring for focus lock. Prism Table: Provided with three leveling screws and engraved lines for prism placement in experiments. Comes complete with Prism Clamp, Grating Holder, Tommy Bar for axis adjustment and Instruction Sheet.
An economically priced Spectrometer, but capable of performing most of the experiments like spectras, angle of prisms, refractive indexes etc. Consists of heavy base with 170 mm diameter circle, divided 0 to 360 degrees, which rotates independently and has locking screw. Collimator: Fixed, with adjustable axis, objective lens with focusing system, variable aperture slit. Telescope: Moveable with set screw and fine motion screw, adjustable axis. Telescope pillar carries vernier scale for accurate measurements. Focusable objective Lens. Ramsden Eyepiece with cross-wires and locking ring for focus lock. Prism Table: Provided with three leveling screws and engraved lines for prism placement in experiments. Comes complete with Prism Clamp, Grating Holder, Tommy Bar for axis adjustment and Instruction Sheet.
Diffraction grating spectroscope is used to show that sunlight can be broken into colored light and to study these colors and their relationships. Students view different types of light and compare the spectra. A preparation for understanding methods used in astronomy. 1" diameter.
Diffraction grating spectroscope is used to show that sunlight can be broken into colored light and to study these colors and their relationships. Students view different types of light and compare the spectra. A preparation for understanding methods used in astronomy. 1" diameter.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
To study Spectral Lines of Pure Elements / Gases. Gas under pressure in the tubes is used to produce a light for spectral analysis. Brightness of light depends on the nature of gas. Optimum intensity, line resolution and longer life. Metal ends with long life electrodes. About 26 cm long, with 90 -100 mm of central capillary. For intermittent use only, not to be used as a lamp source. These are designed to operate 30 seconds ON~30 seconds OFF. Need Spectrum Tube Power Supply or an Induction Coil, sold separately.
A fine instrument for determining the results of curvature of spherical surfaces such as mirrors and lenses. Its micrometer screw is graduated to measure displacement as small as 0.01mm. The instrument has two brass plates and three steel legs. A flat glass plate is provided for support while taking precision readings.
A fine instrument for determining the results of curvature of spherical surfaces such as mirrors and lenses. Its micrometer screw is graduated to measure displacement as small as 0.01mm. The instrument has two brass plates and three steel legs. A flat glass plate is provided for support while taking precision readings.
Clear acrylic trapezoid. With one flat surface frosted to enhance visibility. Bases are 89mm and 40mm. Faces measure 47mm and 35mm.
Clear acrylic trapezoid. With one flat surface frosted to enhance visibility. Bases are 89mm and 40mm. Faces measure 47mm and 35mm.
Designed for spherical mirrors and lenses. Support is 5" tall and has a 1.5" V-shaped grooved wedge to hold mirrors or lenses 38mm to 100mm securely in place.
Designed for spherical mirrors and lenses. Support is 5" tall and has a 1.5" V-shaped grooved wedge to hold mirrors or lenses 38mm to 100mm securely in place.